Mass Air Flow (MAF) Sensor
Typical repair cost:$275 ($150 part + $125 labor)
Manifold Absolute Pressure (MAP) Sensor
Typical repair cost:$200 ($75 part + $125 labor)
Throttle Position Sensor (TPS)
Typical repair cost:$200 ($75 part + $125 labor)
Intake Air Temperature (IAT) Sensor
Typical repair cost:$175 ($50 part + $125 labor)
Idle Air Control (IAC) Valve
Typical repair cost:$300 ($175 part + $125 labor)
Mass Air Flow (MAF) Sensor
1. Disconnect the negative battery cable to prevent electrical shorts. 2. Unplug the MAF sensor’s wiring harness and remove mounting screws or clips. 3. Inspect the sensor element for debris; use an approved MAF cleaner to gently remove contaminants. 4. Reinstall the sensor, ensuring a proper seal, and reconnect the wiring harness. 5. Clear any diagnostic trouble codes (DTCs) and perform a test drive to confirm the repair.
Manifold Absolute Pressure (MAP) Sensor
1. Disconnect the negative battery cable before starting. 2. Disconnect the sensor’s electrical connector and remove securing bolts or clips. 3. Inspect for signs of damage or clogging in the sensor’s port. 4. Install a new sensor or clean the existing one if only lightly contaminated. 5. Reconnect the connector, clear DTCs, and verify proper operation with a test run.
Intake Air Temperature (IAT) Sensor
1. Disconnect the sensor wiring harness and remove it from the intake manifold or airbox. 2. Check for corrosion or buildup around the sensor tip; gently clean with electronic parts cleaner if minor. 3. If damaged or malfunctioning, replace the sensor with a new unit. 4. Reinstall the sensor, reconnect the wiring, and verify that it’s securely fitted. 5. Clear any stored trouble codes and test drive for confirmation.
Idle Air Control (IAC) Valve
1. Disconnect the vehicle’s negative battery cable. 2. Remove the air intake duct if necessary for clear access. 3. Disconnect the IAC valve’s wiring and remove the mounting screws. 4. Use throttle body cleaner to remove carbon deposits from the valve and corresponding passages. 5. Reinstall the cleaned or new valve, reconnect the wiring, and test idle stability.
Throttle Position Sensor (TPS)
1. Disconnect the negative battery cable to eliminate electrical risks. 2. Remove the sensor’s retaining screws and carefully detach the connector. 3. Inspect the sensor and throttle shaft for wear; replace if out of specification. 4. Adjust the new TPS to factory specifications using a multimeter if required. 5. Secure the sensor, reconnect wiring, clear codes, and confirm smooth throttle response.
What is an Air Control Sensor and what does it do
What is an Air Control Sensor
AnAir Control Sensoris a device used to monitor and regulate the quality and flow of air in various environments. These sensors are crucial in maintaining optimal air conditions in both residential and industrial settings.
What Does an Air Control Sensor Do
The primary functions of an Air Control Sensor include:
- Monitoring Air Quality:It detects pollutants, particulate matter, and other harmful substances in the air, ensuring a safe and healthy environment.
- Regulating Air Flow:It helps in controlling the flow of air in HVAC systems, ensuring efficient heating, cooling, and ventilation.
- Maintaining Optimal Conditions:By providing real-time data, it assists in maintaining the desired air conditions, enhancing comfort and energy efficiency.
Overall, Air Control Sensors play a vital role in ensuring air quality and comfort in various applications, from homes to large industrial facilities.
Idle Air Control (IAC) Valve
Rough Idling or Stalling: The engine may idle erratically or stall when coming to a stop.
Inconsistent RPM: You might notice sudden spikes or drops in RPM, especially when idle.
Warning Lights: The “Check Engine” light may illuminate due to related error codes.
Mass Air Flow (MAF) Sensor
Poor Acceleration: The engine might hesitate or struggle to gain speed.
Sudden Changes in Fuel Economy: A noticeable drop in MPG can indicate a failing MAF sensor.
Difficulty Starting: A bad MAF sensor can cause hard starts or immediate stalling.
Manifold Absolute Pressure (MAP) Sensor
Engine Misfires: Misfiring under load or at higher RPM can point to MAP sensor issues.
Reduced Power: The vehicle may feel sluggish or underpowered, especially on inclines.
Check Engine Warning: The ECU may register error codes related to air/fuel mixture.
Intake Air Temperature (IAT) Sensor
Poor Fuel Efficiency: The engine might run too rich or too lean, affecting mileage.
Rough Idle or Hesitation: Incorrect temperature readings can cause rough idling or inconsistent throttle response.
Illuminated Engine Light: A faulty IAT sensor often triggers a diagnostic trouble code.
Inconsistent RPM: You might notice sudden spikes or drops in RPM, especially when idle.
Warning Lights: The “Check Engine” light may illuminate due to related error codes.
Sudden Changes in Fuel Economy: A noticeable drop in MPG can indicate a failing MAF sensor.
Difficulty Starting: A bad MAF sensor can cause hard starts or immediate stalling.
Reduced Power: The vehicle may feel sluggish or underpowered, especially on inclines.
Check Engine Warning: The ECU may register error codes related to air/fuel mixture.
Rough Idle or Hesitation: Incorrect temperature readings can cause rough idling or inconsistent throttle response.
Illuminated Engine Light: A faulty IAT sensor often triggers a diagnostic trouble code.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
