Is Your Reduced Power Light On Don't Risk Further Damage!

Expert Diagnosis & Repairs for All Makes & Models

When your reduced power light illuminates, your vehicle needs immediate attention. Don't compromise your safety or risk costly repairs by delaying.

Why Choose Us:

  • Certified Professional Mechanics
  • Industry-Leading 24-Month/24,000-Mile Warranty
  • Advanced Diagnostic Equipment
  • All Makes & Models Serviced

Don't Wait Until It's Too Late!

Schedule Your Diagnosis Today

Reduced Power Light Repair Cost Estimates

Check Engine + Reduced Power Light
Typical diagnostic time: 1-2 hours
Estimated cost: $125-$250 for diagnosis
Additional repair costs vary based on the underlying issue (sensors, wiring, or mechanical problems)

Transmission Reduced Power Light
Typical diagnostic time: 1.5-2 hours
Estimated cost: $187-$250 for diagnosis
Transmission repairs can range from simple solenoid replacements to major overhauls

Battery/Charging System Reduced Power
Typical diagnostic time: 1 hour
Estimated cost: $125 for diagnosis
Most battery/alternator replacements can be completed within an additional 1-2 hours ($125-$250) plus parts

Electronic Throttle Control Reduced Power
Typical diagnostic time: 1-1.5 hours
Estimated cost: $125-$187 for diagnosis
Throttle body replacement typically requires an additional 1-2 hours ($125-$250) plus parts

Note: These are estimated costs based on our standard rate of $125/hour. Actual repair costs may vary depending on vehicle make, model, and the specific issue identified during diagnosis.

Schedule Your Diagnosis Today

Understanding Reduced Power Light Repairs

When your vehicle's reduced power light illuminates, it's important to address the issue promptly. Here are the typical repair procedures based on common causes:

Electronic Throttle Control (ETC) Issues

Repair Steps:

  1. Diagnostic scan to retrieve error codes
  2. Inspect throttle body for carbon buildup
  3. Clean throttle body if necessary
  4. Test throttle position sensor
  5. Replace throttle body assembly if faulty
  6. Perform ECU relearn procedure

Transmission Problems

Repair Steps:

  1. Perform diagnostic scan
  2. Check transmission fluid level and condition
  3. Inspect transmission solenoids
  4. Test transmission pressure
  5. Replace faulty components as needed
  6. Update transmission control module if required

Failed MAF Sensor

Repair Steps:

  1. Scan for diagnostic trouble codes
  2. Inspect MAF sensor for contamination
  3. Clean MAF sensor if dirty
  4. Test sensor output signals
  5. Replace MAF sensor if defective
  6. Clear codes and verify repair

Faulty Oxygen Sensors

Repair Steps:

  1. Retrieve diagnostic codes
  2. Identify which O2 sensor is failing
  3. Test sensor voltage output
  4. Inspect wiring and connections
  5. Replace faulty oxygen sensor
  6. Clear codes and confirm proper operation

Low Fuel Pressure

Repair Steps:

  1. Check fuel pressure with gauge
  2. Inspect fuel filter
  3. Test fuel pump operation
  4. Check fuel lines for restrictions
  5. Replace fuel pump or filter as needed
  6. Verify proper fuel pressure after repair

Important Note:These are general repair procedures. Specific steps may vary depending on your vehicle's make, model, and year. Always consult your vehicle's service manual or a professional mechanic for model-specific repair instructions.

Regular maintenance can help prevent many of these issues. Schedule routine service checks to keep your vehicle running optimally.

Understanding Reduced Power Lights in Vehicles

reduced-power-light-is-on.webp

When your vehicle's Reduced Power light illuminates, it's important to understand what it means and how to respond. Here's a comprehensive explanation of Reduced Power indicators:

Reduced Engine Power Warning Light

What it is:This warning light typically appears as "REDUCED POWER" or an engine-shaped icon on your dashboard.

What it means:When illuminated, this indicates that your vehicle's computer has detected a system fault and has intentionally reduced engine power to protect the engine from damage.

What it does:The vehicle enters a "limp mode" or "safe mode" where:

  • Engine performance is limited
  • Acceleration is reduced
  • Top speed may be restricted
  • Transmission may remain in lower gears

Common Triggers for Reduced Power Mode

The reduced power mode can be activated by several issues:

  • Faulty throttle body
  • Transmission problems
  • Electronic throttle control issues
  • Failed sensors
  • Wiring problems
  • Computer system malfunctions

Recommended Actions

When this light appears:

  1. Safely pull over if possible
  2. Restart your vehicle to see if the issue resolves
  3. If the light remains on, drive cautiously to a service center
  4. Have a professional diagnostic test performed

Important Note:Continuing to drive with the Reduced Power light on for extended periods could lead to additional vehicle damage. Professional inspection is recommended as soon as possible.

Reduced Power Light Illuminated: Common Symptoms and Causes

Understanding Reduced Power Light Indicators

Check Engine Light
Common signs of failure:

  • Decreased fuel efficiency
  • Rough idling or misfiring
  • Loss of power during acceleration
  • Engine running rough or shaking
Typical service schedule: Have the code read immediately when light appears. Regular maintenance every 30,000 miles can prevent many check engine light issues.

Battery Light
Common signs of failure:

  • Dim headlights or interior lights
  • Clicking sound when trying to start
  • Electrical components working slowly
  • Need to jump-start frequently
Typical service schedule: Battery inspection every 6 months; replacement typically needed every 3-5 years.

Oil Pressure Light
Common signs of failure:

  • Engine making knocking sounds
  • Burning oil smell
  • Engine running louder than usual
  • Oil spots under vehicle
Typical service schedule: Oil changes every 5,000-7,500 miles for conventional oil; 7,500-10,000 miles for synthetic oil.

Temperature Warning Light
Common signs of failure:

  • Steam from under hood
  • Sweet or burning coolant smell
  • Temperature gauge reading high
  • Coolant puddles under vehicle
Typical service schedule: Coolant flush every 30,000 miles or 2 years; regular coolant level checks monthly.

Transmission Warning Light
Common signs of failure:

  • Delayed or rough shifting
  • Grinding or shaking during gear changes
  • Slipping transmission
  • Burning smell while driving
Typical service schedule: Transmission fluid change every 30,000-60,000 miles; inspection every 15,000 miles.

ABS Warning Light
Common signs of failure:

  • Brake pedal pulsating
  • Increased stopping distance
  • Brake pedal becoming hard to press
  • Squealing or grinding noise when braking
Typical service schedule: ABS system inspection every 15,000 miles; brake fluid flush every 2 years.

Note: These are general guidelines. Always consult your vehicle's owner manual for specific maintenance schedules and warning light information.

How It Works

  • Get a quote online or set-up a time to have your vehicle looked at.
  • Pick time slots that work for you, easily, online.
  • We will confirm appointments and send reminders.
  • Our mechanics bring everything that is needed to you.
  • All you have to do is provided a safe area for the work to be performed.

What we need from you

  • A safe place to work on your vehicle
  • No working on the side of busy roads
  • No working on unstable or steep surfaces.
  • We do not perform repairs during severe weather.
  • Authorization from a property owner or management.
  • Repair work done in a parking lot or at your  requires permission.
  • We do not do repairs in areas restricted by law.

Common Questions

Service Area

Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville,  Kentwood, Walker, and Wyoming

Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.

Contact us if you have any questions about where we provide services.

What our customers say: