U1680: U1680: "Module Communication Failure

Definition

The OBD2 code U1680 indicates a "Module Communication Failure," meaning that there is a problem with communication between the vehicle's control modules, which may affect their ability to share data or function properly

Common causes

Faulty wiring or connectors
Failed or malfunctioning control module
Poor ground connections
Corroded or damaged pins in connectors
Intermittent electrical issues
Software or firmware issues in the module
Communication network issues (e.g., CAN bus problems)
Low battery voltage or power supply issues
Aftermarket modifications or installations affecting communication
Faulty sensors or actuators affecting module communication

Common misdiagnoses

Faulty wiring or connectors
Defective control module
Software issues or updates needed
Power supply problems
Grounding issues
Intermittent communication issues
Other communication protocol failures

Troubleshooting steps

1. Check for Other Codes

Use an OBD-II scanner to check for any other trouble codes that may be present. Sometimes, multiple codes can provide more context for the issue
2. Inspect Wiring and Connectors
3. Visually inspect the wiring and connectors associated with the affected module(s). Look for signs of damage, corrosion, or loose connections
4. Pay special attention to the ground connections, as poor grounding can lead to communication issues
5. Check Power Supply
6. Ensure that the affected module is receiving the proper voltage and ground. Use a multimeter to check the power supply to the module
7. If the module is not receiving power, trace the wiring back to the fuse box and check for blown fuses or damaged wires
8. Test the Module
9. If possible, test the affected module by swapping it with a known good module (if available) to see if the problem persists
10. Some modules may have self-diagnostic capabilities; check the module for any internal fault codes
11. Inspect the CAN Bus
12. If the vehicle uses a Controller Area Network (CAN) bus for communication, check the integrity of the CAN bus wiring. Look for shorts, opens, or interference
13. Use an oscilloscope to check the CAN bus signals if you have the equipment and expertise
14. Check for Software Updates
15. Sometimes, communication issues can be resolved with a software update. Check with the vehicle manufacturer for any available updates for the affected module(s)
16. Clear Codes and Test Drive
17. After performing any repairs or inspections, clear the trouble codes using the OBD-II scanner and take the vehicle for a test drive to see if the code returns
18. Consult Technical Service Bulletins (TSBs)
19. Look for any TSBs related to the U1680 code for your specific vehicle make and model. Manufacturers may have specific recommendations or known issues that can help in troubleshooting
20. Professional Diagnosis
21. If the issue persists after performing the above steps, consider seeking help from a professional mechanic or dealership. They may have specialized diagnostic tools and experience with your vehicle. By following these steps, you can systematically diagnose and potentially resolve the U1680 code

Definition

Common causes

Common misdiagnoses

Troubleshooting steps

1. Check for Other Codes

2. Inspect Wiring and Connectors

3. Visually inspect the wiring and connectors associated with the affected module(s). Look for signs of damage, corrosion, or loose connections

4. Pay special attention to the ground connections, as poor grounding can lead to communication issues

5. Check Power Supply

6. Ensure that the affected module is receiving the proper voltage and ground. Use a multimeter to check the power supply to the module

7. If the module is not receiving power, trace the wiring back to the fuse box and check for blown fuses or damaged wires

8. Test the Module

9. If possible, test the affected module by swapping it with a known good module (if available) to see if the problem persists

10. Some modules may have self-diagnostic capabilities; check the module for any internal fault codes

11. Inspect the CAN Bus

12. If the vehicle uses a Controller Area Network (CAN) bus for communication, check the integrity of the CAN bus wiring. Look for shorts, opens, or interference

13. Use an oscilloscope to check the CAN bus signals if you have the equipment and expertise

14. Check for Software Updates

15. Sometimes, communication issues can be resolved with a software update. Check with the vehicle manufacturer for any available updates for the affected module(s)

16. Clear Codes and Test Drive

17. After performing any repairs or inspections, clear the trouble codes using the OBD-II scanner and take the vehicle for a test drive to see if the code returns

18. Consult Technical Service Bulletins (TSBs)

19. Look for any TSBs related to the U1680 code for your specific vehicle make and model. Manufacturers may have specific recommendations or known issues that can help in troubleshooting

20. Professional Diagnosis

21. If the issue persists after performing the above steps, consider seeking help from a professional mechanic or dealership. They may have specialized diagnostic tools and experience with your vehicle. By following these steps, you can systematically diagnose and potentially resolve the U1680 code