U2610 – CAN Communication Bus Off.

The ODBII code U2610 indicates a fault in the CAN (Controller Area Network) communication bus, specifically that the bus is in a “Bus Off” state, meaning it has detected excessive errors and has stopped transmitting to prevent further issues.

The severity of ODBII code U2610 CAN Communication Bus Off is moderate to severe.

Common Causes For: U2609 Invalid Data Received from Vehicle Communication Bus.

• Faulty CAN bus wiring or connectors
• Defective CAN bus module
• Short circuit in the CAN bus
• Open circuit in the CAN bus
• Interference from other electrical components
• Faulty or damaged sensors communicating over the CAN bus
• Software or firmware issues in the control modules
• Low battery voltage or poor power supply to the modules
• Grounding issues in the vehicle’s electrical system
• Corroded or loose connections in the CAN bus network

Common misdiagnosis for U2610 CAN Communication Bus Off.

• Faulty Engine Control Module (ECM)
• Bad Wiring or Connectors
• Defective Body Control Module (BCM)
• Malfunctioning Transmission Control Module (TCM)
• Issues with the Powertrain Control Module (PCM)
• Battery or Charging System Problems
• Faulty Sensors (e.g., wheel speed sensors)
• Incorrectly Diagnosed Communication Issues with Other Modules

Common Troubleshooting Steps

The OBD-II code U2610 indicates a problem with the CAN (Controller Area Network) communication bus, specifically that one of the modules on the bus has gone “off.” This can lead to communication issues between various electronic control units (ECUs) in the vehicle. Here are some common troubleshooting steps to diagnose and resolve the U2610 code:

• Check for Additional Codes: Use an OBD-II scanner to check for any other trouble codes that may be present. Other codes can provide context and help identify the root cause of the issue.
• Inspect the Wiring and Connectors: Visually inspect the wiring and connectors associated with the CAN bus. Look for signs of damage, corrosion, or loose connections.
• Pay special attention to the connectors at the ECUs, as well as any junction points in the wiring harness.
• Test the CAN Bus Voltage: Use a multimeter to measure the voltage on the CAN High and CAN Low wires. The typical voltage levels should be around 2.5V when idle and should fluctuate between 0V and 5V when data is being transmitted.
• If the voltage levels are outside of this range, there may be a fault in the wiring or a malfunctioning ECU.
• Check for Short Circuits or Open Circuits: Use a multimeter to check for continuity in the CAN bus wiring. Look for any short circuits to ground or power, as well as open circuits that could disrupt communication.
• Inspect the ECUs: Identify the ECUs connected to the CAN bus and check for any signs of failure. If one ECU is malfunctioning, it can cause the entire bus to go offline.
• If possible, test the suspect ECU by swapping it with a known good unit.
• Check for Interference: Ensure that there are no aftermarket devices or modifications that could be interfering with the CAN bus communication. This includes devices like alarms, remote starters, or other electronic accessories.
• Perform a Network Test: If you have access to a professional-grade scan tool, perform a network test to check the status of the CAN bus and the connected modules. This can help identify which module is causing the issue.
• Clear the Codes and Test Drive: After performing the above checks and repairs, clear the trouble codes using the OBD-II scanner and take the vehicle for a test drive to see if the code reappears.
• Consult Technical Service Bulletins (TSBs): Check for any manufacturer-specific TSBs related to the U2610 code or CAN bus issues. There may be known fixes or updates available.
• Seek Professional Help: If the issue persists after performing these steps, it may be necessary to consult a professional mechanic or technician who specializes in automotive electronics and CAN bus systems. By following these troubleshooting steps, you should be able to identify and resolve the underlying issue causing the U2610 code.