Service and Cost
ABS Control Module Repair Costs
Basic Diagnostic and Testing
Initial diagnosis of ABS module issues typically takes 1-1.5 hours
Expected cost: $125-$187.50
Module Reprogramming
Software updates and reprogramming usually requires 1-2 hours
Expected cost: $125-$250
Module Repair (Minor)
Simple repairs like corroded connections or minor circuit issues typically take 2-3 hours
Expected cost: $250-$375
Module Repair (Major)
Complex internal repairs or component replacement usually requires 3-4 hours
Expected cost: $375-$500
Complete Module Replacement
Full replacement including removal, installation, and programming typically takes 3-5 hours
Expected cost: $375-$625 (plus part cost)
Note: These are estimated costs based on our standard labor rate of $125/hour. Actual costs may vary depending on vehicle make, model, and specific issues encountered. Parts costs are not included in these estimates.
Additional Considerations:
- Diagnostic fees may be applied to final repair cost
- Some vehicles may require specialized programming equipment
- Warranty available on most repairs
- Emergency service may incur additional charges
ABS Control Module Repair Procedures
Electronic Control Unit (ECU) Repair
Step 1:Diagnostic scanning to confirm ECU failure and retrieve specific fault codes
Step 2:Remove ECU from vehicle following manufacturer's specific removal procedures
Step 3:Inspect circuit board for visible damage (burnt components, corroded connections)
Step 4:Replace damaged components and repair circuit board traces
Step 5:Reprogram ECU with latest manufacturer software
Step 6:Bench test unit before reinstallation
Hydraulic Control Unit (HCU) Repair
Step 1:Verify HCU malfunction through diagnostic testing
Step 2:Safely drain brake fluid from system
Step 3:Document and disconnect brake lines and electrical connections
Step 4:Remove HCU from vehicle
Step 5:Clean and inspect internal valves and components
Step 6:Replace faulty solenoids and valves
Step 7:Reinstall unit and properly bleed brake system
Pump Motor Repair
Step 1:Confirm pump motor failure through diagnostic testing
Step 2:Disconnect battery and electrical connections
Step 3:Remove pump motor assembly
Step 4:Clean and inspect motor components
Step 5:Replace worn brushes and damaged components
Step 6:Test motor function before reinstallation
Step 7:Reinstall and verify proper operation
Wheel Speed Sensor Repair
Step 1:Identify faulty sensor through diagnostic testing
Step 2:Inspect sensor wiring and connections
Step 3:Remove sensor from wheel hub assembly
Step 4:Clean sensor and mounting location
Step 5:Install new sensor if damaged
Step 6:Verify proper sensor operation and signal output
Important Notes:
- All repairs should be performed by certified technicians
- Use only manufacturer-approved replacement parts
- Follow proper safety procedures when working with brake systems
- Perform complete system testing after any ABS component repair
Note: Specific procedures may vary by vehicle make and model. Always consult manufacturer service documentation for detailed instructions.
Understanding ABS Control Modules
No content available for this section.
Common Failure Symptoms of ABS Control Module
ABS Control Module: Signs of Failure & Maintenance Guide
Electronic Control Unit (ECU)
Signs of Failure:
- ABS warning light illuminated on dashboard
- Brake pedal becomes unresponsive
- Inconsistent brake performance
- Traction control system failures
Service Schedule: Generally, the ECU doesn't require regular maintenance but should be diagnosed if warning lights appear. Typical lifespan is 10-15 years.
Wheel Speed Sensors
Signs of Failure:
- ABS light comes on
- Speedometer malfunctions
- Traction control disabled
- Unusual pulsing in brake pedal
Service Schedule: Inspect every 30,000 miles or when brake service is performed. Clean sensors during brake maintenance.
Hydraulic Control Unit
Signs of Failure:
- Brake pedal feels hard or stiff
- Unusual noises during ABS activation
- Brake fluid leaks
- Extended stopping distances
Service Schedule: Inspect during regular brake service (typically every 30,000-50,000 miles). Replace brake fluid every 2-3 years.
ABS Modulator
Signs of Failure:
- Grinding or buzzing sounds during braking
- Erratic brake pedal behavior
- ABS activating at inappropriate times
- Complete ABS system failure
Service Schedule: No regular maintenance required. Inspect if unusual symptoms occur. Average lifespan is 100,000-150,000 miles.
ABS Pump
Signs of Failure:
- Loud humming noise during ABS activation
- Brake pedal pulsation
- Slow brake pedal response
- Complete loss of ABS function
Service Schedule: Inspect during regular brake maintenance. No specific replacement interval, but typically lasts 150,000+ miles under normal conditions.
Important Note: These are general guidelines. Always consult your vehicle's owner manual for specific maintenance schedules and follow manufacturer recommendations.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
