AC System Flush Service Costs
At our standard labor rate of $125/hour, here are the typical costs for different types of AC system flushes:
Chemical Flush
Average Cost: $250-375
Takes approximately 2-3 hours to complete. Includes chemical cleaning solution and labor to flush the entire system. This method is effective for removing light to moderate contamination.
Power Flush
Average Cost: $375-500
Takes approximately 3-4 hours to complete. Includes specialized equipment rental, cleaning solution, and labor. This method is more thorough and recommended for heavily contaminated systems.
Reverse Flush
Average Cost: $312-437
Takes approximately 2.5-3.5 hours to complete. Includes necessary equipment and labor to perform a bidirectional flush of the system. Particularly effective for removing debris from specific components.
Please note:
- Prices may vary depending on vehicle make and model
- Additional parts (if needed) are not included in these estimates
- Severe contamination may require additional time and cost
All services include:
- Complete system inspection
- Evacuation of old refrigerant
- System pressure testing
- Recharge with new refrigerant
Conventional Flush
A conventional flush is the most basic type of AC system flush. Here's the typical procedure:
- System Evacuation:Recover all refrigerant from the system following EPA guidelines
- Component Removal:Disconnect and remove the expansion device and filter drier
- Flushing Process:Connect flushing equipment to the system and circulate cleaning solution through components
- Air Purge:Use compressed air to remove all cleaning solution and debris
- System Reassembly:Install new expansion device and filter drier
- Vacuum Test:Pull vacuum on system to ensure no leaks
- Recharge:Add new refrigerant to manufacturer specifications
Power Flush
A power flush uses specialized equipment to provide a more thorough cleaning. The procedure includes:
- Initial Assessment:Test system pressure and recover refrigerant
- Equipment Setup:Connect power flush machine to system access points
- Cleaning Cycle:Run pressurized cleaning solution through system multiple times
- Purge Cycle:Use compressed air and vacuum to remove all cleaning agents
- System Check:Inspect for cleanliness using sight glass
- Component Replacement:Install new filter drier and expansion valve
- System Charging:Vacuum test and recharge with new refrigerant
Chemical Flush
Chemical flushing uses specific solvents to dissolve contaminants. Here's the process:
- System Preparation:Recover refrigerant and remove expansion device
- Chemical Introduction:Add approved flushing chemical to system
- Circulation:Run chemical through system for specified time period
- Multiple Passes:Repeat flushing process if necessary
- Chemical Removal:Use nitrogen to purge all cleaning chemicals
- Drying Process:Pull vacuum to remove moisture
- System Completion:Install new components and recharge system
Note: All AC system flushes should be performed by certified technicians using appropriate safety equipment and following local regulations.
Understanding AC System Flushes
No content available for this section.
Common Failure Symptoms of Automotive AC Flush Systems
Common Signs of AC System Flush Needs & Maintenance Schedules
Cooling System Flush
Signs of Failure:
- Engine running hotter than normal
- Sweet, syrupy smell from engine area
- Visible rust or discoloration in coolant
- White exhaust smoke
- Low coolant levels frequently
- Sludge buildup in radiator
Typical Service Schedule: Every 30,000 miles or 2-3 years, whichever comes first
Power Steering Flush
Signs of Failure:
- Whining noise when turning
- Stiff or difficult steering
- Dark brown or black power steering fluid
- Squealing during cold starts
- Jerky steering wheel movement
Typical Service Schedule: Every 50,000 miles or 3-5 years, whichever comes first
Transmission Flush
Signs of Failure:
- Delayed or rough shifting
- Grinding or unusual noises
- Dark or burnt-smelling transmission fluid
- Vehicle surging or slipping
- Check engine light illumination
Typical Service Schedule: Every 30,000-60,000 miles, depending on vehicle make and driving conditions
Brake System Flush
Signs of Failure:
- Spongy brake pedal feel
- Dark or cloudy brake fluid
- Brake warning light activation
- Longer stopping distances
- Squealing or grinding when braking
Typical Service Schedule: Every 2 years or 30,000 miles, regardless of mileage
Air Conditioning System Flush
Signs of Failure:
- Weak airflow from vents
- Warm air when AC is on
- Strange odors from vents
- Unusual noises during operation
- Water leaks inside vehicle
Typical Service Schedule: Every 3-5 years or when major AC components are replaced
Note: These are general guidelines. Always consult your vehicle's owner's manual for specific maintenance schedules and follow manufacturer recommendations.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
