U-Joint Repair & Replacement Cost Guide
Labor rates based on $125/hour shop rate. Parts costs may vary based on vehicle make and model.
Basic U-Joint Replacement (Front or Rear)Typical labor time: 1-2 hours
Labor cost: $125-$250
Parts cost: $30-$75 per joint
Total estimated cost: $155-$325
Typical labor time: 2-3 hours
Labor cost: $250-$375
Parts cost: $60-$150 (for two joints)
Total estimated cost: $310-$525
Typical labor time: 2-4 hours
Labor cost: $250-$500
Parts cost: $75-$200 per joint
Total estimated cost: $325-$700
Typical labor time: 3-4 hours
Labor cost: $375-$500
Parts cost: $30-$200 (depending on joint type)
Additional emergency fee: $75-$150
Total estimated cost: $480-$850
Note: These are estimated costs. Final pricing may vary based on vehicle make/model, severity of damage, and additional parts needed. All repairs include basic inspection and greasing of new components.
Warning Signs You Need U-Joint Service:
- Clicking or clunking noise when shifting from drive to reverse
- Vibration at higher speeds
- Squeaking noise during vehicle movement
- Transmission fluid leaks near U-joint location
Universal Joint (U-Joint) Repair Procedure
Here's a step-by-step guide to replacing universal joints on a vehicle's driveshaft:
1. Initial Inspection and Preparation
Steps:
- Raise and secure vehicle on jack stands
- Mark driveshaft orientation for proper reinstallation
- Inspect U-joints for visible damage or excessive movement
2. Driveshaft Removal
Steps:
- Remove driveshaft mounting bolts at the differential
- Carefully lower driveshaft from transmission
- Place driveshaft on workbench
3. U-Joint Removal
Steps:
- Remove snap rings securing the U-joint caps
- Use a press or U-joint removal tool to push out the caps
- Remove old U-joint from yoke
- Clean yoke thoroughly and inspect for damage
4. New U-Joint Installation
Steps:
- Insert new U-joint into yoke
- Press in new bearing caps evenly
- Install new snap rings
- Verify U-joint moves freely without binding
5. Driveshaft Reinstallation
Steps:
- Clean splines on driveshaft and transmission
- Align previously made orientation marks
- Reinstall driveshaft at differential end
- Torque all bolts to manufacturer specifications
6. Final Inspection
Steps:
- Rotate driveshaft by hand to ensure smooth operation
- Check for proper clearance around driveshaft
- Lower vehicle
- Test drive to verify repair
Important Notes:
- Always use quality replacement parts
- Grease new U-joints if they're not pre-greased
- Replace U-joints in pairs when possible
- Consider replacing both ends if one shows significant wear
Note: This procedure may vary depending on vehicle make and model. Always consult your vehicle's service manual for specific instructions.
Understanding Universal Joints (U-joints)
No content available for this section.
Common Signs of U-Joint Failure: Symptoms to Watch For
Universal Joint (U-Joint) Maintenance Guide
Signs of U-Joint Failure
Clunking Noises: A failing U-joint often produces a distinct clunking sound, especially when shifting from drive to reverse or during initial acceleration.
Vibrations: You may experience vibrations in the driveshaft that increase with vehicle speed. These vibrations can be felt through the floor or seat.
Squeaking Sounds: A squeaking noise during low-speed starts or when the vehicle is first put into gear often indicates dry or failing U-joints.
Transmission Fluid Leaks: If the U-joint's seal fails, you might notice transmission fluid leaking near the tail shaft.
Typical Service Schedule
Regular Inspection: U-joints should be inspected every 25,000-30,000 miles as part of routine maintenance.
Lubrication: If your vehicle has greaseable U-joints, they should be lubricated every 10,000 miles or during each oil change.
Replacement Intervals: While there's no set replacement schedule, U-joints typically last 100,000-150,000 miles under normal driving conditions. However, this can vary based on:
- Driving conditions (off-road, heavy towing)
- Vehicle maintenance history
- Environmental factors
Preventive Maintenance: It's recommended to replace U-joints if you notice any play or movement when checking them, even if they haven't completely failed.
Important Note: Failing to address U-joint issues can lead to complete driveline failure, which can be dangerous and result in more expensive repairs.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
