Brake Fluid Level Sensor Repair Costs
Basic Sensor Replacement
Labor Time: 0.5-1 hour
Parts Cost: $20-50
Labor Cost: $62.50-125
Total Estimated Cost: $82.50-175
Complex Sensor Replacement (With Reservoir)
Labor Time: 1-2 hours
Parts Cost: $50-150
Labor Cost: $125-250
Total Estimated Cost: $175-400
Wiring Repair/Connector Replacement
Labor Time: 1-1.5 hours
Parts Cost: $10-30
Labor Cost: $125-187.50
Total Estimated Cost: $135-217.50
Please Note:
- Prices may vary depending on vehicle make and model
- Additional costs may apply if related components need replacement
- Diagnostic fees may apply if extensive testing is required
- All repairs include a thorough brake system inspection
Additional Services Often Recommended:
- Brake fluid flush: $100-150
- Brake system bleeding: $75-125
- Master cylinder inspection: Included in service
Brake Fluid Level Sensor Repair Guide
Safety First:Before beginning any repair, ensure the vehicle is parked on a level surface, the engine is off, and the parking brake is engaged.
Tools Required:
- Socket set
- Screwdrivers
- Clean rags
- New brake fluid level sensor
- Brake fluid
Step-by-Step Repair Procedure:
1. Locate the Brake Fluid Reservoir
- Open the hood
- Locate the brake fluid reservoir (usually near the brake master cylinder)
- Clean the area around the reservoir to prevent contamination
2. Remove the Old Sensor
- Disconnect the electrical connector from the sensor
- Remove the reservoir cap
- Depending on the vehicle model:
- Some sensors unscrew from the cap
- Others may require removal of the entire reservoir
- Some may have retaining clips that need to be released
3. Install the New Sensor
- Compare the new sensor to the old one to ensure proper replacement
- Install the new sensor in reverse order of removal
- Ensure proper seating to prevent leaks
- Reconnect the electrical connector
4. Test the Installation
- Check the brake fluid level
- Top up fluid if necessary
- Turn on the ignition to verify the brake warning light functions correctly
- Check for any leaks around the sensor
Important Notes:
- Use only the specified brake fluid for your vehicle
- Avoid getting brake fluid on painted surfaces
- If the reservoir needs removal, be prepared for some fluid loss
- Consider having a professional perform this repair if you're unsure
Warning:Improper installation can lead to brake system failures. If you're uncertain about any step in this process, please consult a professional mechanic.
Note: This procedure may vary depending on your vehicle's make and model. Always consult your vehicle's service manual for specific instructions.
Understanding Brake Fluid Level Sensors (Switches)
No content available for this section.
Common Failure Symptoms of Brake Fluid Level Sensors: Warning Signs to Watch For
Brake Fluid Level Sensor/Switch: Signs of Failure & Maintenance Guide
Common Signs of Brake Fluid Level Sensor Failure:
1. False Warning Light
The brake warning light on your dashboard illuminates even when the brake fluid level is normal. This is one of the most common signs of a faulty sensor.
2. Warning Light Doesn't Illuminate
The warning light fails to come on when brake fluid is actually low, which can be dangerous as you won't be alerted to low fluid conditions.
3. Intermittent Warning Light
The brake warning light flickers or comes on and off randomly while driving, even when fluid levels remain constant.
4. Corroded Connections
Visual inspection may reveal corrosion or damage to the sensor's electrical connections, which can cause erratic operation.
Maintenance Schedule:
Regular Inspection:
• Inspect the sensor during routine brake fluid checks (every 6 months)
• Check for corrosion or damage during annual brake system inspections
Replacement Guidelines:
• No specific replacement interval is typically recommended
• Replace when faulty operation is detected
• Consider preventive replacement during major brake system overhauls
• Many sensors last the vehicle's lifetime if properly maintained
Best Practices:
• Keep brake fluid clean and at proper levels
• Maintain proper brake fluid type as specified by manufacturer
• Address any warning lights promptly
• Clean connections during brake fluid changes
Important Note: Never ignore a brake warning light, even if you suspect sensor failure. Always have the system professionally inspected to ensure safe operation of your vehicle's braking system.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
