Cruise Control Cable Repair Cost Guide
Mechanical Cruise Control Cable
Labor time: 1-2 hours
Typical cost range: $125-$250
Parts cost: $30-$80
Total estimated cost: $155-$330
Electronic Cruise Control Cable
Labor time: 1.5-3 hours
Typical cost range: $187.50-$375
Parts cost: $75-$200
Total estimated cost: $262.50-$575
Vacuum Operated Cruise Control Cable
Labor time: 2-3.5 hours
Typical cost range: $250-$437.50
Parts cost: $50-$150
Total estimated cost: $300-$587.50
*Note: Prices may vary depending on vehicle make, model, and year. Additional costs may apply if related components need replacement. All estimates based on our standard rate of $125/hour.
What's Included in the Service:
- Diagnostic inspection
- Removal of old cable
- Installation of new cable
- System testing and adjustment
- Final road test verification
Cruise Control Cable Repair Procedures
Accelerator Cable
Common Issues:Cable binding, fraying, or broken connection to throttle body
Repair Steps:
- Locate the accelerator cable running from the cruise control actuator to the throttle body
- Disconnect the negative battery terminal
- Remove any engine covers or components blocking access
- Detach cable from throttle body connection point
- Release cable from cruise control actuator
- Remove cable routing clips along the path
- Install new cable following original routing path
- Secure all mounting clips and connections
- Verify proper cable tension and movement
- Test cruise control operation
Vacuum Cable
Common Issues:Vacuum leaks, deteriorated housing, loss of vacuum pressure
Repair Steps:
- Locate vacuum cable connecting cruise control actuator to engine vacuum source
- Check for visible cracks or damage in the vacuum line
- Release vacuum line connections at both ends
- Remove old vacuum line
- Install new vacuum line following original routing
- Secure connections with proper clamps
- Verify vacuum integrity using vacuum gauge
- Test cruise control engagement
Release/Brake Cable
Common Issues:Cable binding, broken connection at brake pedal, failed disengagement
Repair Steps:
- Locate brake release cable from cruise control to brake pedal assembly
- Disconnect cable from brake pedal bracket
- Trace cable to cruise control unit
- Remove cable mounting clips and fasteners
- Detach cable from cruise control unit
- Install new cable following factory routing
- Connect to brake pedal bracket and adjust tension
- Secure all mounting points
- Verify proper disengagement when brake is applied
- Test complete cruise control operation
Important Safety Notes:
- Always consult vehicle-specific repair manual for exact procedures
- Use only OEM or equivalent quality replacement cables
- Verify proper operation before returning vehicle to service
- Test cruise control system thoroughly in safe conditions
Note: These are general repair procedures. Specific steps may vary by vehicle make and model. Professional installation is recommended for safety-critical systems like cruise control.
Understanding Cruise Control Cables
No content available for this section.
Common Failure Symptoms of Cruise Control Cables
Cruise Control Cable Maintenance Guide
Mechanical Cruise Control Cables
Signs of Failure:
- Cruise control fails to engage or maintain speed
- Cable appears frayed or damaged
- Resistance or sticking when engaging cruise control
- Unusual noise when activating cruise control
- Visible rust or corrosion on cable housing
Service Schedule:
- Inspect every 30,000 miles or 2 years
- Replace if any signs of wear or damage are present
- Lubricate cable connections every 50,000 miles
Electronic Cruise Control Cables
Signs of Failure:
- Intermittent cruise control operation
- Warning lights on dashboard
- System completely non-responsive
- Erratic speed control
- Visible damage to wiring harness
Service Schedule:
- Diagnostic check during regular service intervals
- Visual inspection every 15,000 miles
- Replace connectors if corrosion is present
- Full system check every 60,000 miles
Vacuum-Operated Cruise Control Cables
Signs of Failure:
- Loss of vacuum pressure
- Delayed response in cruise control engagement
- Hissing sounds indicating vacuum leaks
- Inconsistent speed maintenance
Service Schedule:
- Check vacuum lines every 20,000 miles
- Replace vacuum lines every 60,000 miles or if cracking appears
- System pressure test annually
Note: These are general guidelines. Always consult your vehicle's owner manual for specific maintenance schedules and recommendations.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
