Fuel Supply Line Repair Cost Estimates
Fuel Tank to Fuel Pump Line
Typical repair time: 2-3 hours
Estimated cost: $250-$375 (labor)
Additional parts cost: $50-$150
Note: Cost may increase if fuel tank removal is required
Fuel Pump to Fuel Filter Line
Typical repair time: 1-2 hours
Estimated cost: $125-$250 (labor)
Additional parts cost: $30-$100
Most accessible line repair, generally straightforward replacement
Fuel Filter to Fuel Rail Line
Typical repair time: 1.5-2.5 hours
Estimated cost: $187-$312 (labor)
Additional parts cost: $40-$120
May require additional time if fuel rail needs cleaning or replacement
High-Pressure Fuel Lines (Direct Injection)
Typical repair time: 2-4 hours
Estimated cost: $250-$500 (labor)
Additional parts cost: $100-$300
Specialized repair requiring expert handling due to high-pressure system
Return Line to Fuel Tank
Typical repair time: 1.5-2.5 hours
Estimated cost: $187-$312 (labor)
Additional parts cost: $40-$100
May require additional time if routing is complex
*All prices are estimates based on our standard rate of $125/hour. Actual costs may vary depending on vehicle make, model, and condition. Additional parts or complications may affect final pricing.
Fuel Supply Line Repair Procedures
Metal Fuel Lines
Repair Steps:
- Safely depressurize the fuel system
- Locate the damaged section of the metal fuel line
- Clean the area around the damaged section
- Cut out the damaged section using a tubing cutter
- Deburr the cut ends
- Install appropriate compression fittings or unions
- Replace with new section of metal line
- Tighten all fittings to manufacturer specifications
- Pressure test for leaks
Rubber Fuel Lines
Repair Steps:
- Relieve fuel system pressure
- Remove fuel line clamps
- Disconnect the damaged rubber line from connectors
- Clean connection points thoroughly
- Install new rubber fuel line of correct size and rating
- Secure with new clamps at both ends
- Verify proper routing away from heat sources
- Check for leaks under pressure
Quick-Connect Fuel Lines
Repair Steps:
- Release fuel system pressure
- Locate quick-connect release tabs or clips
- Carefully disconnect the fitting using proper tools
- Clean connection points
- Inspect O-rings and replace if necessary
- Install new quick-connect line assembly
- Verify proper connection with audible click
- Test system for leaks
Fuel Injector Lines
Repair Steps:
- Depressurize fuel system completely
- Remove necessary components for access
- Loosen banjo bolts or fittings at both ends
- Remove damaged injector line
- Install new injector line with new washers/seals
- Torque connections to specification
- Bleed fuel system if necessary
- Check for leaks during operation
Important Safety Note:All fuel line repairs should be performed by qualified technicians in a well-ventilated area with proper safety equipment. Always follow manufacturer specifications and safety guidelines.
Warning: Improper fuel line repair can result in dangerous fuel leaks. If you're unsure about any repair procedure, please consult a professional mechanic.
Understanding Fuel Supply Lines

No content available for this section.
Common Failure Symptoms of Fuel Supply Lines: Warning Signs and Indicators
Common Fuel Supply Line Issues & Maintenance Guide
Rubber Fuel Lines
Signs of Failure:
- Cracking or visible deterioration of the rubber
- Fuel odor around the engine bay
- Visible fuel leaks or seepage
- Softening or swelling of the line
Service Schedule: Inspect every 2 years; replace every 5-7 years regardless of condition
Steel Fuel Lines
Signs of Failure:
- Rust or corrosion, especially at bending points
- Pinhole leaks
- Damaged protective coating
- Wet spots or fuel stains along the line
Service Schedule: Inspect annually; replace only when signs of corrosion or damage are present
Nylon Fuel Lines
Signs of Failure:
- Discoloration or brittleness
- Stress cracks at connection points
- Deformation from heat exposure
- Fuel seepage at fittings
Service Schedule: Inspect every 30,000 miles; replace every 8-10 years
High-Pressure Fuel Lines (Direct Injection)
Signs of Failure:
- Engine performance issues
- Fuel pressure warning lights
- Visible leaks at connection points
- Unusual fuel smell during operation
Service Schedule: Inspect every 60,000 miles; replace according to manufacturer specifications
Note: These are general guidelines. Always consult your vehicle's manual for specific maintenance schedules and follow manufacturer recommendations.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.