Ignition Trigger Repair Cost Estimates
Failed Crankshaft Position Sensor
Typical repair time: 1-2 hours
Labor cost: $125-$250
Parts cost: $50-$150
Total estimated cost: $175-$400
Faulty Camshaft Position Sensor
Typical repair time: 1-2 hours
Labor cost: $125-$250
Parts cost: $40-$130
Total estimated cost: $165-$380
Damaged Ignition Coil
Typical repair time: 0.5-1 hour
Labor cost: $62.50-$125
Parts cost: $40-$200 per coil
Total estimated cost: $102.50-$325 per coil
Worn Spark Plugs
Typical repair time: 1-2 hours
Labor cost: $125-$250
Parts cost: $20-$100 for a set
Total estimated cost: $145-$350
Failed Ignition Module
Typical repair time: 1-2 hours
Labor cost: $125-$250
Parts cost: $100-$300
Total estimated cost: $225-$550
Note: These are estimated costs and may vary depending on vehicle make, model, and year. Additional diagnostic time may be required in some cases. Parts costs can vary significantly based on vehicle manufacturer and part quality.
Common Ignition Trigger Repairs by Type
Key Cylinder Issues
Typical Repair Steps:
- Inspect key cylinder for visible damage or wear
- Remove steering column covers to access cylinder
- Extract old cylinder using specialized removal tools
- Install new cylinder assembly
- Cut and program new keys if required
- Test functionality and reassemble steering column
Ignition Switch Problems
Typical Repair Steps:
- Disconnect vehicle battery
- Remove necessary panels and steering column covers
- Disconnect electrical connectors from switch
- Remove mounting screws/hardware
- Install new switch assembly
- Reconnect electrical components
- Test operation before final reassembly
Key Fob Malfunctions
Typical Repair Steps:
- Diagnose specific fob issue (battery, circuit board, buttons)
- Open key fob housing carefully
- Replace battery or damaged components
- Reprogram fob if necessary
- Test all functions
- Reassemble fob housing
Start Button Failures
Typical Repair Steps:
- Diagnose electrical connections and switch functionality
- Remove dashboard panels to access button assembly
- Disconnect electrical connectors
- Remove and replace start button unit
- Reconnect all electrical components
- Program new unit if required
- Test functionality and reassemble panels
Immobilizer System Issues
Typical Repair Steps:
- Connect diagnostic tool to identify specific fault codes
- Access immobilizer antenna or control module
- Replace faulty components as needed
- Reprogram new components to vehicle's ECU
- Clear fault codes
- Test system operation
- Perform final verification of all security features
Important Note:These are general repair procedures. Specific steps may vary by vehicle make, model, and year. Always consult manufacturer specifications and consider having repairs performed by certified professionals.
All repairs should be performed by qualified automotive locksmiths or technicians with proper tools and diagnostic equipment.
Understanding Ignition Triggers
No content available for this section.
Common Ignition Trigger Failure Symptoms and Warning Signs
Common Ignition Trigger Failure Signs and Service Schedules
Distributor
Signs of Failure:
- Engine misfiring or running rough
- Vehicle stalling or hard to start
- Check Engine light illumination
- Clicking or ticking noise from engine
Service Schedule: Inspect every 30,000 miles; replace cap and rotor every 50,000 miles or when worn.
Coil Pack
Signs of Failure:
- Engine misfire under acceleration
- Rough idle
- Decreased fuel economy
- Check Engine light (specifically misfire codes)
- Engine backfiring
Service Schedule: No set schedule; replace when failing. Typically lasts 80,000-100,000 miles.
Crankshaft Position Sensor
Signs of Failure:
- Engine won't start or hard starting
- Engine stalling
- Check Engine light activation
- Intermittent engine operation
Service Schedule: No regular maintenance required; replace when failing. Usually lasts vehicle lifetime unless damaged.
Camshaft Position Sensor
Signs of Failure:
- Poor acceleration
- Rough idle
- Transmission shifting issues
- Check Engine light illumination
Service Schedule: No scheduled maintenance; replace when showing signs of failure.
Optical Trigger
Signs of Failure:
- Intermittent starting issues
- Engine timing inconsistencies
- Erratic engine performance
- Complete failure to start
Service Schedule: Inspect during routine maintenance; clean when dirty. Replace if damaged or malfunctioning.
Hall Effect Sensor
Signs of Failure:
- Engine stalling
- Erratic spark timing
- Poor acceleration
- No-start condition
Service Schedule: No regular maintenance required; replace when failing. Typical lifespan varies by vehicle make and model.
Note: Service intervals may vary based on vehicle manufacturer recommendations and operating conditions. Always consult your vehicle's owner manual for specific maintenance schedules.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
