Accelerator Cable Repair Cost Guide
Basic Accelerator Cable Adjustment
Labor Time: 0.5 hours
Typical Cost: $62.50
This includes basic cable adjustment and lubrication without parts replacement.
Accelerator Cable Replacement (Standard Vehicle)
Labor Time: 1-1.5 hours
Typical Cost: $125-187.50 + parts ($30-75)
Total Range: $155-262.50
Common repair for most domestic and Asian vehicles with straightforward access.
Accelerator Cable Replacement (Complex Access)
Labor Time: 2-3 hours
Typical Cost: $250-375 + parts ($40-100)
Total Range: $290-475
Required for some European vehicles or models with complicated routing/access.
Electronic Throttle Connection Repair
Labor Time: 1-2 hours
Typical Cost: $125-250 + parts ($50-150)
Total Range: $175-400
For vehicles with electronic throttle control systems requiring connector or wiring repairs.
Note: Prices are estimates only. Final costs may vary based on vehicle make/model, parts availability, and additional repairs needed. All services include comprehensive system testing.
Accelerator Cable Repair Procedures by Type
Traditional Cable-Operated Throttle
Common Issues:Fraying, binding, stretching, or broken cable
Repair Steps:
- Locate cable routing from pedal assembly to throttle body
- Remove cable end from throttle body and pedal assembly
- Remove any cable housing retaining clips
- Extract old cable completely
- Install new cable following original routing
- Attach cable ends to throttle body and pedal
- Adjust cable tension per manufacturer specifications
- Test pedal operation and verify smooth movement
Electronic Throttle Control (Drive-by-Wire)
Common Issues:Sensor failure, wiring damage, connector problems
Repair Steps:
- Connect diagnostic scanner to verify fault codes
- Remove pedal assembly from vehicle
- Inspect wiring harness for damage
- Check connector terminals for corrosion or damage
- Replace entire pedal assembly if sensor is faulty
- Install new pedal assembly
- Clear fault codes with scanner
- Perform relearn procedure if required
- Test pedal operation and verify proper sensor readings
Cruise Control Cable
Common Issues:Cable binding, stretching, or breakage
Repair Steps:
- Locate cruise control cable routing
- Disconnect cable from cruise control actuator
- Remove cable from throttle body connection
- Remove cable housing clips and guides
- Install new cable following original routing
- Connect to actuator and throttle body
- Adjust cable tension per specifications
- Test cruise control operation
Important Notes:
- Always consult vehicle-specific repair manuals before beginning work
- Use only OEM or high-quality replacement parts
- Proper cable routing is crucial to prevent binding or interference
- Some repairs may require specialized tools or diagnostic equipment
- Electronic throttle repairs often require dealer-level diagnostic capabilities
Note: Repair procedures may vary by vehicle make, model, and year. Professional diagnosis is recommended for accurate repair assessment.
Understanding Accelerator Cables
No content available for this section.
Common Failure Symptoms of Accelerator Cables: Warning Signs and Indicators
Signs of Accelerator Cable Failure & Maintenance Guide
Mechanical Accelerator Cables
Signs of Failure:
- Sticky or sluggish accelerator pedal response
- Pedal feels loose or spongy
- Cable appears frayed or damaged
- Inconsistent engine response to pedal input
- Squeaking or grinding noise when pressing the pedal
Service Schedule:
Inspect every 30,000 miles or 2 years, whichever comes first. Replace if signs of wear are present. In high-use vehicles, consider inspection every 20,000 miles.
Electronic Throttle Cables
Signs of Failure:
- Check Engine light illumination
- Delayed throttle response
- Engine surging or hesitation
- Erratic idle speed
- Vehicle entering "limp mode"
Service Schedule:
Electronic throttle systems typically don't require regular cable replacement. However, sensors and electronic components should be diagnosed during routine vehicle service (every 30,000-50,000 miles). Clean throttle body every 60,000 miles.
Drive-By-Wire Systems
Signs of Failure:
- Throttle position sensor errors
- Electrical connection issues
- Intermittent acceleration problems
- System warning lights
- Complete loss of throttle response
Service Schedule:
Diagnostic scanning recommended every 30,000 miles. System calibration may be required if performance issues arise. Physical components typically last the vehicle's lifetime unless electrical issues develop.
Note: These are general guidelines. Always consult your vehicle's manual for specific maintenance schedules and follow manufacturer recommendations.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
