Air Intake Hose
Parts Cost:$40–$80
Labor Time:0.5 hours
Labor Cost:$62.50
Total Cost:$102.50–$142.50
Hose Clamps
Parts Cost:$2–$10
Labor Time:0.2 hours
Labor Cost:$25
Total Cost:$27–$35
Gaskets or O-Rings
Parts Cost:$5–$15
Labor Time:0.3 hours
Labor Cost:$37.50
Total Cost:$42.50–$52.50
Air Filter Housing Seal
Parts Cost:$10–$25
Labor Time:0.4 hours
Labor Cost:$50
Total Cost:$60–$75
Air Intake Duct
Inspection:Examine the duct for cracks, splits, or warping.
Removal:Loosen the hose clamps and gently detach the duct from the air filter housing and throttle body.
Repair/Replacement:If minor damage is found, use a suitable sealant or tape for temporary repair. For significant damage, replace the duct entirely.
Reinstallation:Slide the duct back in place, ensuring a proper seal, then tighten all hose clamps securely.
Hose Clamps
Inspection:Check for rust, stripped screws, or bent bands.
Removal:Unscrew or unclamp them to free the hose from adjacent components.
Repair/Replacement:If clamps are misshapen or show signs of corrosion, replace them with new clamps of the correct size.
Reinstallation:Position the clamps evenly over the hose and tighten them to the manufacturer’s recommended torque, making sure there are no leaks.
Rubber Connectors
Inspection:Look for any tears, soft spots, or brittleness in the rubber.
Removal:Loosen the clamps securing the connectors, then slide them off carefully.
Repair/Replacement:If the rubber is cracked or excessively worn, replace with new connectors that match the original size and shape.
Reinstallation:Fit the connectors back onto each component, ensuring a tight seal before reapplying and tightening clamps.
PCV or Vacuum Line Port
Inspection:Ensure the port and any attached hoses aren’t clogged, cracked, or loose.
Removal:Detach any vacuum lines by carefully sliding them off the port.
Repair/Replacement:Clear blockages with compressed air or replace faulty lines/port if there’s significant damage.
Reinstallation:Reattach lines securely, making sure each connection is snug to prevent air leaks.
Mass Air Flow (MAF) Sensor Port
Inspection:Check the sensor port and the sealing grommet for damage or debris.
Removal:Disconnect the electrical connector from the MAF sensor, then loosen any screws or clamps securing it.
Repair/Replacement:Clean the sensor port with non-residue cleaner if dirty. Replace if the port or grommet is damaged.
Reinstallation:Carefully position the MAF sensor back into the port, secure it with screws/clamps, and reconnect the harness.
Air Filter Housing Connection
Inspection:Confirm there are no cracks or misalignments where the hose meets the air filter housing.
Removal:Unlatch or unscrew the housing cover as needed, then slide the hose off gently.
Repair/Replacement:If cracks are detected near the connection, use epoxy or a specialized sealant for minor issues; replace the housing if damage is extensive.
Reinstallation:Align the hose onto the housing securely, ensuring a snug fit before re-securing the cover and any clamps.
What is an Air Box Hose and what does it do
No content available for this section.
Air Filter Housing
Signs of Failure:
- Visible cracks or damage on the plastic casing
- Loose or broken clips preventing a tight seal
- Accumulation of dirt or debris inside the housing
When to Repair: If you notice hissing sounds, unusual rattles, or the housing not sealing correctly around the filter, it’s time for a repair or replacement.
Air Filter
Signs of Failure:
- Excessive dirt or dust build-up on the filter material
- Poor engine performance or reduced fuel efficiency
- Unusual engine noises due to restricted airflow
When to Repair: Clean or replace the filter if it appears visibly clogged or if you experience sluggish acceleration.
Flexible Air Intake Hose
Signs of Failure:
- Cracks, splits, or tears in the rubber material
- Loose fit around the clamps or connectors
- Whistling or sucking noises indicating air leakage
When to Repair: If you discover any cracks or detect air leaks, replace or securely re-clamp the hose to maintain proper airflow.
Clamps and Connectors
Signs of Failure:
- Rust or corrosion on metal clamps
- Broken or missing clamp screws
- Loosened connectors that no longer hold the hose tightly
When to Repair: Tighten or replace clamps and connectors if you hear rattling or notice slack in the air intake components.
Mass Air Flow (MAF) Sensor Mount
Signs of Failure:
- Loose or uneven seal around the sensor mount
- Check engine light triggered by airflow-related issues
- Irregular engine idle or poor fuel efficiency
When to Repair: If you see any damage or feel the sensor mount is not secure, reseal or replace it to ensure accurate airflow readings.
Air Box to Throttle Body Connection
Signs of Failure:
- Gaps or leaks where the hose meets the throttle body
- Reduced engine power due to unmetered air entering the system
- Unstable idle and hesitation during acceleration
When to Repair: Check and reseal or replace any worn gaskets and ensure a tight fit to prevent performance issues.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
