Engine Intake Manifold Runner Vacuum Control Motor Repair Costs
Below are the typical repair costs for Engine Intake Manifold Runner Vacuum Control Motor services. All estimates include our standard labor rate of$125 per hourplus parts.
Diagnostic Service
Initial diagnosis of runner control issues:$125-$250
Includes computer scanning and visual inspection of the vacuum control system.
Basic Repairs
Vacuum Control Motor Replacement Only
Labor: 1-2 hours ($125-$250)
Parts: $150-$300
Total Cost Range: $275-$550
Moderate Repairs
Motor Replacement with Runner Cleaning
Labor: 2-3 hours ($250-$375)
Parts: $150-$300
Cleaning materials: $50
Total Cost Range: $450-$725
Complex Repairs
Complete System Overhaul
Labor: 3-5 hours ($375-$625)
Parts: $300-$500
Additional components: $100-$200
Total Cost Range: $775-$1,325
Note: Prices may vary depending on vehicle make, model, and year. Additional repairs may be necessary based on inspection findings. All estimates are approximate and subject to change.
Common Additional Services:
- Intake manifold gasket replacement: $200-$400
- Vacuum line replacement: $100-$250
- Runner cleaning service: $150-$300
Engine Intake Manifold Runner Vacuum Control Motor Repair Guide
Diagnosis Phase:
- Connect diagnostic scanner to verify fault codes related to runner control
- Perform visual inspection of vacuum lines and electrical connections
- Test electrical connectivity to the control motor
- Check vacuum system integrity
Preparation Steps:
- Allow engine to cool completely
- Disconnect negative battery terminal
- Document and photograph vacuum line routing
- Clear workspace around intake manifold area
Removal Procedure:
- Remove engine cover (if applicable)
- Disconnect electrical connector from control motor
- Label and carefully remove vacuum lines
- Remove mounting bolts securing the control motor
- Carefully extract the control motor from its mounting location
Installation Steps:
- Clean mounting surface thoroughly
- Install new gasket if required
- Position new control motor in mounting location
- Install and torque mounting bolts to specification
- Reconnect vacuum lines in correct order
- Reconnect electrical connector
- Reinstall engine cover
Post-Installation Verification:
- Reconnect battery
- Clear any stored fault codes
- Start engine and verify proper operation
- Check for vacuum leaks
- Perform test drive to ensure proper functionality
Important Notes:
- Always use OEM or high-quality replacement parts
- Ensure proper vacuum line routing to prevent future issues
- Replace any damaged vacuum lines during installation
- Some vehicles may require ECU adaptation after replacement
Note: Specific steps may vary by vehicle make and model. Always consult your vehicle's service manual for model-specific instructions and torque specifications.
Engine Intake Manifold Runner Vacuum Control Motor: What Is It and How Does It Work
No content available for this section.
Common Failure Symptoms of Engine Intake Manifold Runner Control (IMRC) Vacuum Motor
Engine Intake Manifold Runner Vacuum Control Motor: Signs of Failure & Maintenance
Common Signs of Failure
Check Engine Light
One of the first indicators is often an illuminated check engine light, typically accompanied by codes P2004-P2017, which are related to runner control system malfunctions.
Poor Engine Performance
You may notice:
- Reduced acceleration, especially at lower RPMs
- Rough idle or hesitation
- Decreased fuel efficiency
- Inconsistent power delivery
Unusual Noises
Listen for:
- Clicking or ticking sounds from the intake area
- Vacuum leaks (hissing sounds)
- Rattling when accelerating
Maintenance Schedule
Regular Inspection
The vacuum control motor should be inspected:
- Every 60,000 miles
- During routine tune-ups
- When performing intake manifold service
Preventive Maintenance
- Clean intake runners every 30,000-50,000 miles
- Check vacuum lines for cracks or damage annually
- Test vacuum control motor operation during scheduled maintenance
Note: Specific maintenance intervals may vary by vehicle manufacturer and model. Always consult your vehicle's owner manual for exact maintenance schedules.
If you experience any of these symptoms, we recommend having your vehicle inspected by a qualified technician to prevent potential damage to your engine's intake system.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
