Manifold Temperature Sensor Repair Costs
Bank 1 Manifold Temperature Sensor Replacement
Labor Time: 1-1.5 hours
Labor Cost: $125-$187.50
Parts Cost: $75-$150
Total Estimated Cost: $200-$337.50
Bank 2 Manifold Temperature Sensor Replacement
Labor Time: 1-1.5 hours
Labor Cost: $125-$187.50
Parts Cost: $75-$150
Total Estimated Cost: $200-$337.50
Important Notes:
- Costs may vary depending on vehicle make and model
- Some luxury or European vehicles may have higher parts costs
- Additional diagnostic time may be required if multiple issues are present
- All repairs include basic system testing and clearing of fault codes
Additional Services Often Required:
- Diagnostic scan: $75-$125
- Intake manifold gasket replacement (if needed): $200-$400
- Wiring harness repair (if damaged): $100-$250
Please note: These are estimated costs based on our standard labor rate of $125/hour. Final pricing may vary based on specific vehicle requirements and conditions found during inspection.
Manifold Temperature Sensor Repair Procedures
Bank 1 Manifold Temperature Sensor Repair
Tools Required:
- Socket set
- Ratchet
- Extension bar
- Anti-seize compound
Repair Steps:
- Allow engine to cool completely to avoid burns
- Locate the Bank 1 manifold temperature sensor (typically on the driver's side)
- Disconnect the negative battery terminal
- Unplug the electrical connector from the sensor
- Remove the sensor using the appropriate socket size
- Compare new sensor with old to ensure correct replacement
- Apply anti-seize compound to threads of new sensor
- Install new sensor and torque to manufacturer specifications
- Reconnect electrical connector
- Reconnect battery terminal
- Start engine and check for proper operation
Bank 2 Manifold Temperature Sensor Repair
Tools Required:
- Socket set
- Ratchet
- Extension bar
- Anti-seize compound
Repair Steps:
- Allow engine to cool completely to avoid burns
- Locate the Bank 2 manifold temperature sensor (typically on the passenger's side)
- Disconnect the negative battery terminal
- Unplug the electrical connector from the sensor
- Remove the sensor using the appropriate socket size
- Compare new sensor with old to ensure correct replacement
- Apply anti-seize compound to threads of new sensor
- Install new sensor and torque to manufacturer specifications
- Reconnect electrical connector
- Reconnect battery terminal
- Start engine and check for proper operation
Important Notes:
- Always refer to vehicle-specific repair manual for exact specifications
- Ensure proper torque specifications are followed to prevent damage
- Check for any related diagnostic trouble codes after repair
- Some vehicles may require relearning procedures after sensor replacement
Note: These procedures may vary depending on vehicle make, model, and year. Professional installation is recommended if you're unsure about performing these repairs.
Understanding Manifold Temperature Sensors
No content available for this section.
Common Failure Symptoms of Manifold Temperature Sensor (MTS)
Manifold Temperature Sensor: Signs of Failure and Maintenance Guide
Signs of Failure
Check Engine Light
One of the first and most common indicators of a failing manifold temperature sensor is an illuminated check engine light. The engine control module (ECM) will detect irregular readings and trigger the warning light.
Poor Engine Performance
A malfunctioning sensor can cause:
- Rough idling
- Decreased fuel efficiency
- Hesitation during acceleration
- Hard starting conditions
Failed Emissions Test
Since the sensor helps regulate air-fuel mixture, a faulty sensor can cause the vehicle to fail emissions testing due to improper fuel mixture.
Typical Service Schedule
Regular Inspection
The manifold temperature sensor should be inspected during routine maintenance, typically every 60,000 miles or when symptoms occur.
Cleaning Schedule
Professional cleaning is recommended every 30,000-40,000 miles to remove carbon deposits and ensure accurate readings.
Replacement Guidelines
- Average lifespan: 80,000 to 100,000 miles
- Replacement recommended when showing signs of failure
- Should be replaced during major engine work
Preventive Maintenance
Regular engine tune-ups and maintaining clean air filters can help extend the sensor's life and ensure accurate readings.
Note: Actual service intervals may vary based on vehicle make, model, and driving conditions. Always consult your vehicle's manual for specific maintenance schedules.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
