Cruise Control Brake Release Switch Repair Costs
Basic Switch Replacement
Labor Time: 0.5-1 hour
Parts Cost: $30-75
Total Estimated Cost: $92-200
Complex Switch Replacement (With Brake Pedal Assembly)
Labor Time: 1.5-2 hours
Parts Cost: $100-250
Total Estimated Cost: $287-500
Electrical Harness Repair
Labor Time: 1-2 hours
Parts Cost: $40-100
Total Estimated Cost: $165-350
Note: Prices may vary depending on vehicle make, model, and year. Additional costs may apply if related components require repair or replacement. All labor calculated at $125/hour shop rate.
Common Signs of Failure:
- Cruise control won't engage
- Cruise control disengages unexpectedly
- Brake lights staying on
- Check engine light illuminated
Warranty:Most replacement parts come with a 12-month/12,000-mile warranty on parts and labor.
Cruise Control Brake Release Switch Repair Procedures
Mechanical Brake Light Switch
Tools needed:Basic hand tools, multimeter
Repair steps:
- Locate the brake light switch near the brake pedal assembly
- Disconnect the negative battery terminal
- Unplug the electrical connector from the switch
- Remove the mounting nuts/hardware securing the switch
- Test switch functionality with a multimeter
- Install new switch if testing confirms failure
- Adjust switch position to ensure proper brake pedal engagement
- Reconnect electrical connector and battery
- Test brake lights and cruise control operation
Hydraulic Brake Switch
Tools needed:Basic hand tools, brake fluid, brake bleeding kit
Repair steps:
- Locate the switch on the master cylinder or brake line
- Place a drain pan under the work area
- Disconnect the electrical connector
- Carefully unscrew the switch from its mounting location
- Install new switch with appropriate thread sealant
- Reconnect electrical connector
- Bleed brake system to remove any air
- Top off brake fluid reservoir
- Test brake operation and cruise control function
Electronic Brake Switch
Tools needed:Diagnostic scanner, basic hand tools
Repair steps:
- Connect diagnostic scanner to verify switch fault
- Remove necessary trim panels to access switch
- Disconnect the negative battery terminal
- Unplug electrical connectors from switch assembly
- Remove mounting hardware
- Install new switch assembly
- Reconnect electrical connections and battery
- Use scanner to clear any stored fault codes
- Verify proper operation of brake lights and cruise control
Important Safety Note:Always consult your vehicle's service manual for specific procedures and torque specifications. Proper brake system operation is critical for vehicle safety.
Note: These are general repair procedures. Specific steps may vary by vehicle make and model. Professional installation is recommended for brake system components.
Understanding Cruise Control Brake Release Switches
No content available for this section.
Common Failure Symptoms of the Cruise Control Brake Release Switch
Cruise Control Brake Release Switch: Signs of Failure & Maintenance Guide
Common Signs of Failure
1. Cruise Control Won't Disengage
- Cruise control remains active even when brake pedal is pressed
- Requires manual cancellation using cruise control button
- Poses significant safety risk if not addressed immediately
2. Cruise Control Won't Engage
- System refuses to activate when attempting to set cruise control
- Brake light may stay illuminated on dashboard
- Switch may send incorrect signals to vehicle's computer
3. Intermittent Operation
- Cruise control works inconsistently
- System may disengage randomly
- May require multiple brake pedal presses to disengage
Typical Service Schedule
Regular Inspection:
- Visual inspection every 30,000 miles or 2 years
- Test functionality during routine brake service
- Check electrical connections annually
Preventive Maintenance:
- Clean switch contacts every 50,000 miles
- Replace switch every 80,000-100,000 miles as preventive measure
- Earlier replacement may be needed based on usage and conditions
Important Note: These are general guidelines. Specific maintenance schedules may vary by vehicle make, model, and year. Consult your vehicle's manual or a certified technician for exact maintenance requirements.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
