Power Seat Switch Repair Cost Guide
Main Power Seat Control Switch
Typical repair time: 1-1.5 hours
Labor cost: $125-$187.50
Parts cost: $150-$300
Total estimated cost: $275-$487.50
Seat Position Memory Switch
Typical repair time: 1-2 hours
Labor cost: $125-$250
Parts cost: $200-$400
Total estimated cost: $325-$650
Lumbar Support Switch
Typical repair time: 1-1.5 hours
Labor cost: $125-$187.50
Parts cost: $100-$250
Total estimated cost: $225-$437.50
Seat Heater/Cooler Switch
Typical repair time: 1-2 hours
Labor cost: $125-$250
Parts cost: $150-$350
Total estimated cost: $275-$600
Recliner Switch
Typical repair time: 1-1.5 hours
Labor cost: $125-$187.50
Parts cost: $100-$200
Total estimated cost: $225-$387.50
Note: Prices may vary based on vehicle make, model, and year. Additional costs may apply if related components need replacement. All estimates include our standard labor rate of $125/hour.
Power Seat Switch Repair Procedures
Driver's Side Master Switch
Common Issues:Multiple seat movement failures, intermittent operation, or complete non-response
Repair Steps:
- Remove the seat switch trim panel from the seat
- Disconnect the electrical connector from the switch assembly
- Remove mounting screws securing the switch to the trim panel
- Test switch connectivity with a multimeter to confirm failure
- Replace entire switch assembly with new OEM part
- Reconnect electrical connections
- Test all seat movements before final reassembly
- Reinstall trim panel
Passenger Side Switch
Common Issues:Single direction failure or complete switch non-response
Repair Steps:
- Remove seat trim panel to access switch
- Unplug electrical connector
- Remove mounting screws (typically 2-3 screws)
- Verify switch failure using multimeter
- Install new switch assembly
- Reconnect wiring
- Verify proper operation
- Reinstall trim panel
Memory Position Switch
Common Issues:Memory positions not storing or recalling, button non-response
Repair Steps:
- Access the memory switch module (usually on driver's door panel)
- Remove door panel if necessary
- Disconnect electrical connections
- Remove mounting hardware
- Test switch functionality
- Replace memory switch module
- Reprogram memory positions after installation
- Verify all memory functions work correctly
- Reassemble door panel
Lumbar Support Switch
Common Issues:No lumbar movement, stuck in position, grinding noise
Repair Steps:
- Remove seat side trim panel
- Locate lumbar switch assembly
- Disconnect electrical connections
- Remove mounting hardware
- Test switch with multimeter
- Replace switch assembly if faulty
- Reconnect all wiring
- Test lumbar operation in all directions
- Reinstall trim panel
Important Notes:
- Always disconnect vehicle battery before beginning any electrical repairs
- Use proper trim removal tools to prevent damage to interior panels
- Document wire connections before disconnecting
- Keep all mounting hardware organized
- Test all seat functions thoroughly before completing repair
Note: Repair procedures may vary by vehicle make and model. Always consult the appropriate service manual for specific instructions.
Understanding Power Seat Switches
No content available for this section.
Common Failure Symptoms of Power Seat Switch Systems
Common Power Seat Switch Failure Symptoms and Maintenance Guide
Master Power Seat Switch
Signs of Failure:
- Intermittent or no response when pressing switch
- Seat moves in only certain directions
- Grinding or clicking noise when operating switch
- Switch feels loose or wobbly
Service Schedule: No regular maintenance required, but inspect every 50,000 miles or if issues arise.
Memory Seat Switch
Signs of Failure:
- Memory positions not saving correctly
- Memory recall not functioning
- Indicator lights not illuminating
- Erratic seat movement when recalling positions
Service Schedule: Test functionality every 30,000 miles or annually. Reprogram if necessary.
Lumbar Support Switch
Signs of Failure:
- Lumbar support not inflating/deflating
- Switch feels stuck or unresponsive
- Inconsistent operation
- Unusual noises from lumbar mechanism
Service Schedule: Check operation every 25,000 miles. Clean switch assembly if needed.
Recliner Switch
Signs of Failure:
- Seat back doesn't adjust smoothly
- One-sided operation only
- Switch requires excessive force
- Delayed response when activated
Service Schedule: Inspect switch mechanism during regular service intervals (30,000 miles).
Note: These are general guidelines. Specific maintenance schedules may vary by vehicle make and model. Always consult your vehicle's owner manual for manufacturer-recommended service intervals.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
