Torque Rod Repair & Replacement

Don't Let a Failing Torque Rod Put You at Risk

Experience precise handling and optimal vehicle stability with our professional torque rod services.

Industry-leading24-month/24,000-mile warranty
ASE-certified mechanics with specialized expertise
All makes and models serviced
Same-day service available

Torque Rod Repair Service Pricing Guide

Front Torque Rod (V-Rod)
Typical repair time: 1.5 - 2 hours
Expected cost: $187.50 - $250.00
Includes removal, inspection, bushing replacement, and reinstallation

Rear Torque Rod
Typical repair time: 1 - 1.5 hours
Expected cost: $125.00 - $187.50
Includes removal, inspection, bushing replacement, and reinstallation

Transverse Torque Rod
Typical repair time: 2 - 2.5 hours
Expected cost: $250.00 - $312.50
Includes removal, inspection, bushing replacement, and reinstallation

Additional Notes:

  • Labor rate: $125/hour
  • Prices do not include parts cost
  • Actual repair time may vary based on vehicle condition and accessibility
  • Severe rust or damage may require additional labor time

Please note: These are estimated costs. Final pricing may vary depending on specific vehicle requirements and conditions encountered during service.

Torque Rod Repair Procedures by Type

V-Rod/Radius Rod

Common repair steps:

  1. Remove the torque rod from the vehicle
  2. Clean and inspect the rod ends and center section
  3. Remove worn bushings using specialized press tools
  4. Clean and inspect the eye sections for damage or deformation
  5. Press in new premium rubber or polyurethane bushings
  6. Test for proper bushing seating and alignment
  7. Reinstall on vehicle and torque to manufacturer specifications

Transverse Torque Rod

Common repair steps:

  1. Remove from vehicle, noting orientation
  2. Inspect center section for straightness and damage
  3. Remove old bushings from both ends
  4. Clean bushing housing areas thoroughly
  5. Install new bushings using appropriate press tools
  6. Check for proper bushing compression
  7. Reinstall ensuring correct positioning and torque settings

Trailing Arm

Common repair steps:

  1. Remove trailing arm assembly
  2. Inspect entire arm for cracks or structural damage
  3. Remove worn bushings from both pivot points
  4. Clean and prepare bushing housings
  5. Press in new bushings using correct tooling
  6. Verify bushing alignment and seating
  7. Reinstall arm and torque all fasteners to spec

Torque Rod with Bar Pin End

Common repair steps:

  1. Remove torque rod from suspension
  2. Inspect bar pin ends for wear or damage
  3. Remove old rubber or polyurethane inserts
  4. Clean bar pin channels thoroughly
  5. Install new rubber or polyurethane inserts
  6. Check for proper insert fitment
  7. Reinstall and torque according to specifications

Important Notes:

  • Always use proper safety equipment and follow manufacturer guidelines
  • Inspect all hardware and replace if necessary
  • Use appropriate press tools to avoid damage to components
  • Consider replacing both sides even if only one side shows wear
  • Always verify proper torque specifications before installation

Note: These are general repair procedures. Specific vehicles may require additional or modified steps. Always consult the vehicle manufacturer's service manual for detailed instructions.

Understanding Torque Rods

torque-rod.webp

No content available for this section.

Signs and Symptoms of Torque Rod Failure

Torque Rod Failure Signs & Maintenance Guide

V-Rod / V-Torque Rod

Signs of Failure:

  • Excessive vibration during acceleration or braking
  • Cracking or separation of rubber bushings
  • Visible rust or corrosion around mounting points
  • Unusual clunking noise when shifting gears

Service Schedule: Inspect every 50,000 miles or annually. Replace if signs of wear are present.

Transverse Torque Rod

Signs of Failure:

  • Lateral movement of axle
  • Uneven tire wear
  • Squeaking during turns
  • Visible bushing deterioration

Service Schedule: Inspection recommended every 30,000-40,000 miles. Replace bushings if deterioration is evident.

Longitudinal Torque Rod

Signs of Failure:

  • Forward/backward axle movement
  • Driveline vibration
  • Difficulty maintaining proper pinion angle
  • Visible bushing wear or separation

Service Schedule: Inspect every 50,000 miles. Replace if bushings show signs of wear or separation.

Upper Torque Rod

Signs of Failure:

  • Excessive driveline angle changes
  • Vibration during acceleration
  • Visible bushing deterioration
  • Metal fatigue around mounting points

Service Schedule: Inspect during regular maintenance intervals (approximately every 50,000 miles). Replace if wear is evident.

Important Note: These are general guidelines. Actual service intervals may vary based on application, operating conditions, and manufacturer specifications. Always consult your vehicle's manual or a qualified technician for specific maintenance requirements.

How It Works

  • Get a quote online or set-up a time to have your vehicle looked at.
  • Pick time slots that work for you, easily, online.
  • We will confirm appointments and send reminders.
  • Our mechanics bring everything that is needed to you.
  • All you have to do is provided a safe area for the work to be performed.

What we need from you

  • A safe place to work on your vehicle
  • No working on the side of busy roads
  • No working on unstable or steep surfaces.
  • We do not perform repairs during severe weather.
  • Authorization from a property owner or management.
  • Repair work done in a parking lot or at your  requires permission.
  • We do not do repairs in areas restricted by law.

Common Questions

Service Area

Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, GrandvilleKentwood, Walker, and Wyoming

Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.

Contact us if you have any questions about where we provide services.

What our customers say: