Clutch Repair Cost Estimates
Clutch Replacement
A complete clutch replacement typically takes between 4-8 hours depending on the vehicle make and model.Labor costs range from $500-$1,000at our shop rate of $125/hour. Parts (including clutch kit, flywheel, and related components) typically cost between $300-$800.Total cost usually ranges from $800-$1,800.
Clutch Master Cylinder Replacement
Replacing a clutch master cylinder usually requires 1-2 hours of labor.Labor costs range from $125-$250. Parts typically cost between $100-$300.Total cost usually ranges from $225-$550.
Clutch Slave Cylinder Replacement
A slave cylinder replacement typically takes 1-3 hours.Labor costs range from $125-$375. Parts usually cost between $75-$200.Total cost usually ranges from $200-$575.
Clutch Cable Replacement
Replacing a clutch cable usually takes 1-2 hours.Labor costs range from $125-$250. Parts typically cost between $50-$150.Total cost usually ranges from $175-$400.
Clutch Hydraulic Line Repair
Hydraulic line repairs typically take 1-3 hours.Labor costs range from $125-$375. Parts usually cost between $50-$200.Total cost usually ranges from $175-$575.
Note: These are estimated costs. Actual prices may vary depending on vehicle make, model, and condition. Additional parts or repairs may be necessary after inspection.
Clutch Repair Procedures by Type
Standard Mechanical Clutch
Typical repair steps:
- Remove transmission (requires lifting vehicle and supporting engine)
- Remove old clutch assembly and flywheel
- Inspect flywheel surface and either machine or replace if necessary
- Install new clutch disc, pressure plate, and release bearing
- Align clutch components using alignment tool
- Reinstall transmission
- Bleed hydraulic system (if hydraulically operated)
- Adjust clutch pedal free play
- Road test vehicle
Hydraulic Clutch
Typical repair steps:
- Diagnose hydraulic system for leaks or failures
- Remove transmission (if clutch disc/pressure plate replacement needed)
- Replace master and/or slave cylinder
- Replace hydraulic lines if corroded or damaged
- Bleed hydraulic system thoroughly
- Replace clutch components if necessary (following mechanical clutch steps)
- Verify proper pedal feel and engagement
- Road test vehicle
Dual-Mass Flywheel Clutch
Typical repair steps:
- Remove transmission
- Remove old clutch assembly
- Remove and replace dual-mass flywheel (cannot be machined)
- Install new clutch kit designed for dual-mass flywheel
- Replace release bearing and guide tube
- Carefully align all components
- Reinstall transmission
- Reset clutch adaptive values (if applicable)
- Road test vehicle
Self-Adjusting Clutch
Typical repair steps:
- Remove transmission
- Remove self-adjusting clutch assembly
- Install new self-adjusting clutch kit as complete unit
- Replace release bearing
- Ensure proper alignment of components
- Reinstall transmission
- Reset clutch adjustment mechanism
- Verify proper self-adjustment operation
- Road test vehicle
Multi-Plate Clutch
Typical repair steps:
- Remove transmission
- Carefully remove multi-plate clutch assembly
- Document plate arrangement during disassembly
- Replace all friction plates and steel plates
- Install new springs and retainers
- Reassemble in correct order
- Verify proper clearances
- Reinstall transmission
- Road test vehicle
Important Notes:
- All clutch repairs require specialized tools and expertise
- Labor times vary significantly by vehicle make and model
- Additional repairs may be necessary depending on system inspection
- Always replace hydraulic components in pairs
- Use only manufacturer-recommended parts and fluids
Understanding Different Types of Clutches
No content available for this section.
Clutch Failure Symptoms: Warning Signs You Shouldn't Ignore
Signs of Clutch Failure
Manual Transmission Clutch
Warning Signs:
- Difficulty engaging gears or grinding noise when shifting
- Clutch pedal feels spongy, soft, or sticks to the floor
- Burning smell while driving
- Clutch slipping (engine revs but vehicle doesn't accelerate properly)
- Vibration in the clutch pedal
- Squealing or chirping noise when pressing clutch pedal
Typical Service Schedule:
- Average lifespan: 50,000 to 100,000 miles
- Inspect during regular maintenance intervals (30,000-60,000 miles)
- Replace hydraulic fluid every 30,000 miles
Automatic Transmission Clutch
Warning Signs:
- Delayed or rough engagement when shifting from park/neutral
- Shuddering or vibration during acceleration
- Transmission slipping between gears
- Unusual noises during gear changes
- Check Engine light illumination
Typical Service Schedule:
- Transmission fluid change every 30,000-60,000 miles
- Inspect clutch packs during transmission service
- Major service typically needed between 100,000-150,000 miles
Dual-Clutch Transmission (DCT)
Warning Signs:
- Jerky or hesitant acceleration
- Unusual noises during gear changes
- Delayed response when accelerating
- Transmission warning light
- Excessive vibration during gear changes
Typical Service Schedule:
- DCT fluid change every 40,000-50,000 miles
- System diagnostic check every 30,000 miles
- Mechatronic unit inspection every 60,000 miles
Important Note: These are general guidelines. Always consult your vehicle's owner manual for specific maintenance schedules and follow manufacturer recommendations.
How It Works
- Get a quote online or set-up a time to have your vehicle looked at.
- Pick time slots that work for you, easily, online.
- We will confirm appointments and send reminders.
- Our mechanics bring everything that is needed to you.
- All you have to do is provided a safe area for the work to be performed.
What we need from you
- A safe place to work on your vehicle
- No working on the side of busy roads
- No working on unstable or steep surfaces.
- We do not perform repairs during severe weather.
- Authorization from a property owner or management.
- Repair work done in a parking lot or at your requires permission.
- We do not do repairs in areas restricted by law.
Common Questions
Service Area
Our primary service area is greater Grand Rapids and includes Comstock Park, East Grand Rapids, Grandville, Kentwood, Walker, and Wyoming
Our secondary service area is provided by our Belding location and includes: Belding, Greenville, Ionia and the sorrounding areas.
Contact us if you have any questions about where we provide services.
